LOCATION: FRANCE

Rislone^® Engine Oil Stop Leak Concentrate is specially designed to stop seal and gasket leaks caused by normal engine wear and age.

Works with ALL gasoline and diesel engines using conventional, high kilometer / mileage and synthetic engine oil.

World’s Most Trusted Stop Leak Brand Since 1921

 Stops and Seals Motor Oil Leaks

 Safe and Easy to Use

 Restores Gaskets & Seals to Stop & Prevent Engine Oil Leaks

INSTRUCTIONS:

Add entire bottle of stop leak to engine oil at or between oil changes. Leaks usually stop in 300 km or 3 days of driving. If leak continues, a second application may be required or mechanical attention is needed.

DOSAGE:

One bottle treats up to 5 liters of oil. For larger systems use 1 bottle for every 5 liters of oil capacity.  On small 4 cycle engines, use approximately 65 mL per liter of capacity.

Rislone® Engine Oil Treatment Conditioner and Lubricant is high quality penetrating lubrication oil, combined with protective engine additives and special cleaning agents.  Its multi-grade formula allows the oil to flow freely and provides protection over a broader temperature range.  Sludge and other harmful deposits within engines can alter tolerances, stick rings, cause noisy valves & lifters, and plug oil passages and screens.  The unique Rislone formula is designed to penetrate into bearing surfaces, piston rings and ring grooves, where sludge and varnish is likely to form.  These deposits are gradually removed and held in suspension until they are trapped in the filter or removed with the next oil change. Regular use of Rislone Engine Treatment, with oil and filter changes at the proper intervals, will keep such deposits to a minimum. A cleaner engine is a better lubricated engine with less friction & wear.

Works on gasoline, diesel and turbo engines with conventional, high kilometer / mileage and synthetic engine oils.

PROTECTING ENGINES SINCE 1921

REDUCES FRICTION AND WEAR

QUIETS NOISY LIFTERS AND VALVES

REMOVES & PREVENTS SLUDGE

MAXIMIZES ENGINE POWER

INSTRUCTIONS:

Add entire bottle of Rislone Engine Oil Treatment to engine crankcase.  Maximum performance formula may be used anytime, at or between oil changes.  For best protection, use Rislone Engine Oil Treatment at every oil change.

DOSAGE:

In passenger car and light truck engines, use one bottle for a 3,5 to 6 liters.  For larger systems, add one bottle for every 5 liters of capacity.  For severely dirty engines, use two bottles of Rislone Engine Oil Treatment and change the oil after 150 kilometers of driving.

Rislone^® One Seal™ multipurpose stop leak effectively seals all minor engine oil, transmission and power steering system leaks. It’s specifically designed to stop seal and gasket leaks caused by normal wear and age.

3X Sealer

Works with ALL Engine Oil, Transmission Fluid and Power Steering Fluids

 Safe and Easy to Use

 World’s Most Trusted Stop Leak Brand Since 1921

WARNING: 

Do not use in the brake system or add to antifreeze /coolant.

INSTRUCTIONS:

Add entire bottle of One Seal to specific leaking system reservoir.

DOSAGE:

One bottle will treat one engine oil, transmission fluid or power steering fluid system leak.  Leaks usually stop in 350 km, or 3 days of driving.  If leak continues, a second application may be required or mechanical attention is needed.

Rislone^® High Kilometre / Mileage Compression Repair with Ring Seal is a concentrated proprietary blend of high-shear and premium polymers developed for higher mileage engines that are suffering from decreased or uneven compression.  Low compression can be caused by normal engine wear and decreased sealing between the piston rings and cylinder walls.  The non-dispersant olefin copolymers fill scratches & grooves in cylinder walls to increase and stabilize compression in all cylinders.  Compression Repair renews worn engines, rebuilds compression, restores lost power and repairs engine blow-by.  In addition, Compression Repair helps vehicles pass emission tests.

Some signs of decreased compression include loss of power, poor fuel economy, oil consumption, blue smoke from exhaust, plug fouling and engine noise or vibration.

The Viscosity Improver (VI) is designed specifically to provide an optimum balance of shear stability and thickening efficiency required in old and modern engines.  This performance additive meets the most severe passenger car and truck engine requirements.

Product works by freeing sticky rings and filling gaps & scratches in cylinder walls, eliminating blow-by and compression loss while also reducing friction and wear.  Blow-by is usually caused by gaps in internal engine parts resulting from excess wear.

Rislone Compression Repair with Ring Seal does not contain any harmful lead or other metals that  could damage the inside of your engine or be burned and contaminate emissions components and the environment.

Works on petrol, LPG and diesel engines with conventional, high kilometre and synthetic engine oils.

INSTRUCTIONS:

Add entire bottle of COMPRESSION REPAIR WITH RING SEAL to engine crankcase at or between oil changes.  Do not overfill.  Results will either be immediate or noticeable within a few days of driving.  Install Compression Repair every 10,000 km or with every oil change.

DOSAGE:

One bottle treats 4 to 6 litres of oil.  For larger engines, use one bottle for every 5 litres of capacity.  On 4-Stroke ATV, Motorcycle and small engines, including wet clutch applications, use approximately 100 mL per litre of oil capacity.

Modern conventional motor oils lack the metal protection older engines require.  Use as directed in gasoline & diesel engines, antique & classic cars, hot rods, trucks, motorcycles, tractors, agricultural & industrial machinery, off road and all racing applications to boost ZINC and PHOSPHOROUS ZDDP levels needed to protect flat tappet camshafts, lifters and other valvetrain components from wear.  Specially designed for engines requiring SL / CI rated oil and older.

• Rislone^® Hy-per Lube^® Zinc ZDDP Supplement is a petroleum oil performance “booster” containing ZDDP (zinc dialkyldithiophosphate) Zinc and Phosphorous EP (extreme pressure) additives along with mixed esters to help protect internal engine components including pistons, flat tappet camshafts, lifters, pushrod tips and the rest of the valve train.
• High performance formula stabilizes the motor oil to insure against viscosity and thermal breakdown.
• Reduces friction & wear, especially at start-up, helping to eliminate dry starts. Less friction means less wear and a cooler running, longer lasting engine.
• Clinging action keeps bearings and other internal engine parts lubricated where normal oil fails.
• Enhances regular motor oil turning it into a high performance lubricant for use in older engines and racing applications.
• Rislone Hy-per Lube ZDDP Supplement works with all petroleum-based motor oils including conventional, high mileage / kilometre and synthetic formulas to make newer oils backwards compatible for older and high performance engines.
• Protecting Engines Since 1921

* Prevents Camshaft Wear

* Reduces Piston Scuffing

*  Increases Engine Life

Oil Viscosity is approximately equivalent to a high 20 weight motor oil, which should not change existing motor oil viscosity at the recommended dosage rate.

NOTE:  Do not use as an engine break in additive.  Rislone Engine Oil Supplement with Zinc Treatment contains the correct amount of ZDDP and other additives important to protecting your engine for everyday use.

Directions: 

For best protection, use with every oil change.  Can be used during oil change, or added in-between oil changes.  Do not overfill.

PETROL / GASOLINE ENGINES (Cars & Light Trucks)

1996 and older – Add one bottle to engine crankcase.

1997 to 2004 – Add approximately ½ bottle (162 mL) to engine.

2005 and newer—Add approximately 1/4 bottle (81 mL) to engine.

DIESEL ENGINES (Light, Medium & Heavy-Duty)

2006 and older – Add one bottle to engine crankcase for every 5 litres of oil capacity.

2007 and newer –Add 1/2 bottle to engine.

OTHER APPLICATIONS

For 4-stroke marine & motorcycles ATV (non-wet clutch), agricultural, industrial and racing engines— Add 65 mL for every litre of capacity.

TYPICAL TEST RESULTS INDICATE:

GASOLINE ENGINES

With typical SN rated oil at a 7% dosage rate expect levels to be raised to a total of:

Zn Zinc 1700 – 1800 ppm

Rislone^® Oil Seal^™ Engine Oil Burning & Leak Repair is the fastest, safest way to solve your vehicles oil consumption issues.  Your vehicle is a good candidate for this solution if it does not use more than one litre of oil per day. Depending on the severity of the leak, the first thing you may notice is the engine oil level decreasing. There may be bluish (blue and/or gray) smoke coming from the tailpipe upon starting the vehicle, more noticeably after it has been sitting for a while, like overnight.  Your engine could also be consuming oil and you don’t see any smoke or leaks, as it is being burned gradually. Use with all types of motor oil, including regular petroleum, high kilometre, synthetic blends and fully synthetic. Can be used to top off oil when low, or to replace a half litre of oil when performing an oil change. Works with ALL petrol, LPG and diesel engines.

• Repair Valve Stem Seal Leaks
• Stop Blue Exhaust Smoke
• Reduce Oil Consumption
• Reinforced with Synthetic Polymers
• One Dosage Stops Smoking & Oil Burning
• Safe & Easy to Use, and Works Quickly
• Best Repair Formula Money Can Buy
• Synthetic Blend, for All Engines

INSTRUCTIONS:

1) Turn engine off.

2) Shake well. Remove the oil fill cap and pour Oil Seal^™ Engine Oil Burning & Leak Repair into engine per dosage chart. Do not overfill. Reinstall cap.

3) Drive/idle engine for at least 15 minutes to mix thoroughly with oil and activate product to start working.

4) Top off engine (add oil as needed) and leave Oil Seal^™ Engine Oil Burning & Leak Repair in the system for continued protection.  Drive vehicle as normal.  Most valve seal issues are corrected in 400 kilometres or 3 days of driving.  For best results use with every other oil change.

DOSAGE:

One bottle treats oil capacity from 4 litres to 6 litres.

Use ½ bottle for oil capacity from 2 litres to 3.9 litres.

For larger systems use 1 bottle for every 5 litres. On 4-Stroke ATV, Motorcycle and small engines, including wet clutch applications, use approximately 100 mL per litre of oil capacity.

THE BEST Oil Seal™ Engine Oil Burning & Leak Repair MONEY CAN BUY

Advanced, specially-formulated synthetic polymers, along with premium valve seal restoring additives, work together better than all other regular treatments to create a long lasting repair.

SAFE TO USE ON:

Petrol Engines

Diesel Engines

LPG Engines

Turbocharged Engines

Racing Engines

WORKS ON ALL:

3, 4, 5, 6 and 8 Cylinders

Synthetic and Petroleum Oil

Cars, Trucks, Utes, Vans and SUV’s

VALVE GUIDE SEAL TYPES

(3 basic styles)

O-ring

Umbrella (Deflector)

Positive

*Top-Hat

*Metal Clad

*Ring and Band

*Ring and Spring

VALVE GUIDE SEAL MATERIALS

Nylon

Nitrile (NBR or Buna N)

Polyacrylate (PA)

Silicone

Viton (Fluoroelastomer)

Teflon

What is a Valve Guide Seal?

 The simple answer is: A seal that fits around the valve stem and valve guide to prevent oil leakage.

The more detailed answer is: A valve guide seal, also known as a valve stem seal or valve seal, is located on the engine cylinder head inside of the valve springs. An automotive engine can have as few as 8 valves seals, or up to 32. These are located on the intake and exhaust valves and have a pretty difficult job to do as they need to allow some oil to (pass so that the valve stem and guide receive lubrication), but need to prevent larger amounts of oil from going into the combustion chamber to be burned.  When too much oil is burned the vehicle will consume oil, emit blue exhaust smoke and cause valve carbon build up. This is bad for the environment, and also the emission system on the vehicle.

Leaking valve seals can account for over half of all oil consumption issues. It is amazing that such a small part that only costs a few dollars each can cause so many big problems.

Rislone^® Head Seal™ Blown Head Gasket Repair is the fastest, safest way to solve your vehicle’s coolant-related head gasket issues. Your vehicle is a good candidate for this solution if it can idle for 15 minutes without overheating or having to add coolant.  Use with ALL types of 50-50 mix coolant including yellow, orange, pink, red, blue and green silicate based & non-silicate based (OAT / HOAT) antifreeze, and/or water.  Unlike other products, no draining or thermostat removal is required.  Works with ALL gasoline and diesel engines.  This also is the best additive to use in all racing applications.

This professional-strength sealant penetrates leaking, blown or damaged head gasket area, drying to form a seal actually stronger than the original head gasket itself.  The strongest formula available to stop all other coolant leaks in plastic, cast iron, copper and aluminum radiators, heater cores, freeze plugs, gaskets, intake manifolds, cylinder heads and engine blocks. It also contains Xtreme Cool^™, a specialized additive that stops overheating and reduces water temperature.

• Permanently:

*Repair Blown Head & Intake Gasket Leaks

*Seal Warped / Cracked Heads & Blocks

*Stop Overheating & Coolant Loss

*Fix Bubbles Entering Cooling System

• Reinforced with Carbon Fibers
• One Dosage Stops All Head Gasket Coolant Problems
• Safe & Easy to Use, and Works Quickly
• The Best Repair Formula Money Can Buy
• Antifreeze Compatible, No Flushing Required

Note

Protect from freezing.

Instructions For Use

1) Install only in a cold engine.  Shake bottle well.  Remove radiator cap and pour the correct amount of product in per the dosage chart.  Fill radiator and reservoir / overflow tank to proper level and reinstall radiator cap.

TIP: Radiator cap may be on top of radiator, on engine, mounted on a hose, or a screw cap on the pressurized reservoir overflow tank.

2) Turn heater on hot and fan on high.  Run engine until thermostat opens or normal operating temperature is reached.  Turn vehicle off and allow engine to cool.  This may take up to 30 minutes or longer.

3) Top off radiator (add coolant as needed) and either run engine at high idle (approximately 1200 RPM’s for vehicles with a tachometer) or gently drive for 15 minutes.  Turn vehicle off and allow engine to cool.

4) Top off radiator and leave Rislone HEAD Seal Blown Head Gasket Repair in system for continued protection.  Drive vehicle as normal. Most leaks seal instantly, but some can take additional thermocycles which happen over a few days of usage.

Dosage

One bottle treats cooling systems from 9.5 liters to 19 liters.  Use ½ bottle for smaller cooling systems from 5.5 liters to 9.49 liters.  For larger systems use 1 bottle for every 19 liters of cooling capacity.  In very small systems, use 55 ml per liter of capacity.

Rislone^® Power Steering Stop Leak Concentrate is specially designed to stop seal and O-ring leaks caused by normal power steering wear and age.  Works on rack & pinion units, gear boxes and pumps.  Keeps power steering seals soft and pliable.  Non-corrosive, non-clogging and non-foaming.

Works with ALL domestic, import and heavy duty power steering fluids; including petroleum, mineral oil, synthetics and ATF automatic transmission fluid.

World’s Most Trusted Stop Leak Brand Since 1921

Stops and Seals Power Steering Fluid Leaks

Safe and Easy to Use

Restores O-rings & Seals to Stop & Prevent Steering Leaks

INSTRUCTIONS:

Add Stop Leak to power steering reservoir to restore fluid level.  Do not overfill.  Leaks usually stop in 300 km or 3 days of driving. If leak continues, a second application may be required or mechanical attention is needed.

DOSAGE:

One bottle treats up to 2.5 liters of fluid.  For larger systems, use 1 bottle for every 2 liters of fluid capacity.

Rislone® Liquid Aluminum™ Cooling System / Radiator & Heater Core Stop Leak is the best radiator stop leak money can buy.  Scientifically formulated to permanently seal coolant leaks that are the cause of most overheating problems.  Liquid Aluminum is part of the next generation stop leak line which not only seal leaks, but also conditions the system.  Contains Xtreme Cool™ which stops overheating and reduces water temperature.  Safely and easily seal leaks in plastic, aluminum and metal (copper / steel) radiators, heater cores, gaskets and freeze plugs.  It will not harm the cooling system, no draining is required.  Use with ALL types of traditional or extended life coolant including yellow, orange, pink, red, blue, purple and green silicate based & non-silicate based (OAT/HOAT) 50-50 mix antifreeze, and/or water.  For most vehicles leaks seal instantly.

Safe to Use and Seals Instantly

Works with All Types of Antifreeze Coolant or Water 

Use in Cars, Trucks, Utes, Vans, SUV’s and RV’s

STOP LEAK – Liquid Aluminum safely seals leaks in plastic, aluminum and metal radiators, heater cores, gaskets and freeze plugs.  One of the few products to meet ASTM D6107 requirements for Stop Leak Additives used in Engine Coolants.

XTREME COOL™ – Xtreme Cool reduces the surface tension of coolant increasing the wetting ability.  This improves heat transfer reducing coolant temperature helping to prevent overheating and leaks.

DANGER:  Opening the cooling system while the engine is hot or running may cause severe burns.

NOTE:  Cooling systems that are dirty or partially clogged should be flushed before usage.

Protect from freezing.

DOSAGE:

Add one bottle for 5, 6, 8 and 10 cylinder engines.  Use 1/2 bottle in 3 and 4 cylinder engines.  One bottle treats cooling systems from 9.5 liters to 15 liters.   Use 1/2 bottle for cooling systems from 5.5 liters to 9.4 liters.  For larger systems use one bottle for every 12 liters of cooling system capacity.  Small engines or other small systems use approximately 40 mL per liter of fluid capacity.

INSTRUCTIONS:

1) Allow engine to cool.  Make sure engine is cool enough so radiator cap can be safely removed.

2) Shake well.  Pour Liquid Aluminum directly into radiator.  One bottle treats systems up to 15 liters.  Use 1/2 bottle in 3 and 4 cylinder engines.

TIP:  If direct access to radiator is not available, install in overflow tank.

3)  Fill radiator and overflow tank to proper level and reinstall radiator cap.

4) Drive/idle engine for 15 to 20 minutes.  If leak continues, second application may be required or mechanical attention is needed.  For severe leaks, like a blown head gasket, it is recommended to use Rislone Head Gasket Fix.

5)  Leave Rislone Liquid Aluminum in cooling system for continued protection.

Rislone^® Radiator Stop Leak Sealer is specially designed to stop minor cooling system leaks and drips caused by normal cooling system wear and age.

Works with ALL Types and Colors of Antifreeze Coolant and / or Water

Stops & Seals Coolant Leaks

Seals Leaks in Radiators, Gaskets, Heater Cores & Freeze Plugs

DANGER:  Opening the cooling system while the engine is hot or running may cause severe burns.

NOTE:  Cooling systems that are dirty or partially clogged should be flushed before usage.

Protect from freezing.

INSTRUCTIONS:

Shake well.  Pour Stop Leak into a cool radiator.  If direct access to radiator is not available, install in overflow / reservoir tank.  Fill radiator and overflow tank to proper level and reinstall cap.  Drive / idle engine for 15 to 30 minutes.  If leak continues, a second application may be required, or mechanical attention is needed.  Leave Rislone in the cooling system for continued protection.

DOSAGE:

Passenger cars and light trucks—Use one bottle for 6 & 8 cylinders and half bottle for 4 cylinder engines.  Small engines or other small systems use approximately 20 mL per liter of fluid capacity.

Over the road and heavy-duty equipment—Install one bottle for every 15 liters of coolant capacity.

Rislone® Xtreme Cool Super Radiator Flush will help your cooling system by removing deposits that build up over time causing overheating.  Heavy duty formulation is specially designed to clean solder bloom, oily residue, rust and scale.  Non-acid formula is safe to use on all cooling system materials including copper, aluminum, plastic and rubber.

• Use every time changing antifreeze.
• Neutralizes acids that cause corrosion and helps prevent formation of future scale deposits. 
• Heavy Duty Xtreme Clean™ formula cleans entire cooling system.
• Clean systems run cooler.

Caution: Never remove radiator cap if engine is hot.

Note:  Protect from freezing.

Dosage: One bottle cleans up to 15 liter systems.

Disposal: Observe local laws and regulations.  Where permitted, dispose of in a sanitary sewer system.  Never pour on the ground or in a storm sewer system.

Instructions For Use

Step 1. Allow engine to cool  Drain system.  Close drain.

Step 2. Add entire contents of bottle and refill system with water.  For larger cooling systems use, use one bottle of Super Radiator Flush for every 12 litres.  Reinstall cap.

Step 3. Start engine.  After reaching normal operating temperature, run engine for 10 minutes with heater control on high.

NOTE: For extremely dirty systems, run an additional 10 minutes.

Step 4. Allow engine to cool.  Flush cooling system and reservoir until water runs clear.

TIP: Using a flush “T” with garden hose works best for final cleaning.

Step 5. Close drain. Refill cooling system and reservoir with manufacturer’s recommended antifreeze / water mixture.  For best results add Rislone Hy-per Cool Super Coolant after flushing the system, as the metal surfaces inside the system are now cleaned and primed for optimal heat transfer performance and corrosion protection.

Rislone® Hy-per Cool™ Radiator Cleaner & Super Flush will help your cooling system by removing deposits that build up over time causing overheating.  Heavy duty formulation is specially designed to clean solder bloom, oily residue, rust and scale.  Contains water pump lubricant and corrosion inhibitors, so will not damage the pump like other brands.

• Fast, easy and safe to use on all cooling system materials, including plastic and aluminum.  Works with all cooling systems.
• Eliminates damaging coolant deposits, reducing engine operating temperature to prevent overheating.
• Neutralizes acids that cause corrosion and helps prevent formation of future scale deposits. 
• Heavy Duty Xtreme Clean™ formula cleans entire cooling system.
• Removes deposits and coolant gel for a complete cleaning in 30 minutes or less.
• Use every time changing coolant for light flushing or heavy duty cleaning.
• Clean systems run cooler

Caution:

Never remove radiator cap if engine is hot.

Dosage:

One bottle treats up to 15 liter systems.

Directions:

Step 1. With engine off and cool, drain system.

Step 2. Close drain and add entire contents of bottle, then refill system with water.  Reinstall cap, start engine, turn heat on high, and run engine for 10 to 15 minutes.  Turn engine off and allow to cool, drain system.

Step 3. Flush cooling system and reservoir until water runs clear.

TIP: Using a flush “T” with garden hose works best for final cleaning.

Step 4. Refill cooling system and reservoir with manufacturer’s recommended antifreeze/water mixture.

For best results add Rislone Hy-per Cool Super Coolant after flushing the system, as the metal surfaces inside the system are now cleaned and primed for optimal heat transfer performance and corrosion protection.

Disposal

Observe local laws and regulations.  Where permitted, dispose of in a sanitary sewer system.  Never pour on the ground or in a storm sewer system.

Rislone^® Hy-per Cool™ Super Coolant contains very high cloud point surfactants designed to provide maximum wetting (coolant surface tension reduction) at normal and high cooling system operating temperatures.  This supercharged coolant mixture eliminates bubbles, resulting in improved heat transfer to dissipate heat more efficiently in the entire cooling system.  Real world and laboratory testing shows reduced engine temperatures by up to 17°C helping to prevent overheating.  Super Coolant lubricates and protects the water pump, and helps prevent corrosion, erosion and electrolysis of all parts of the cooling system, including aluminum, plastics, rubber and more.  Works with all colors and types of antifreeze coolant including extended life, or straight water.

Provides extra protection against higher engine temperatures.  Up to 41°C lower cylinder head temperatures (CHT) enhance engine efficiency, proving better fuel economy, power and performance.

Use in petrol classic cars, hot rods, trucks, utes, RV’s, motorcycles, automotive, heavy duty, diesel, powersports ATV, off road, racing, towing and most anything else with a cooling system.

Racing approved and safe to use from drag strips to the oval track.  Contains no glycol.  Provides no antifreeze protection.  Always check for freeze protection if needed.

• The Best Coolant Additive Money Can Buy
• Reduces Engine Temperature
• Prevents Overheating
• Provides Maximum Corrosion Protection
• Supercharges Cooling System Performance

Caution:

Never remove radiator cap if engine is hot.

Directions: 

Add one bottle to treat 11.5 to 19 liter systems.  For larger and smaller systems add 30 mL per liter of capacity.  Can be added to overflow tank, but it will take 4 to 5 heating and cooling cycles for product to fully enter the system.  For continued protection re-treat once per year, and every time changing coolant.

Rislone^® Hy-per Diesel™ Complete Fuel System Treatment improves the quality of Diesel fuel by increasing its cleaning ability, adding lubrication, removing contaminants, fighting corrosion, and helping to prevent the fuel from gelling & going bad. This one dual cavity bottle contains the same amount of additives equal to a bottle of regular injector & complete fuel system cleaner, anti-gel cold flow improver, fuel stabilizer & conditioner, Cetane booster & diesel treatment, ULSD sulfur substitute, and UCL pump & injector lubricant.  Simply put, it is the best all in one diesel fuel additive money can buy.

Works with ALL:  Ultra Low Sulfur Diesel (ULSD), Regular Diesel, Biodiesel Blends, Direct Injected (DI), Indirect Injected (IDI), Turbo Direct Injected (TDI), High-Pressure Common Rail (HPCR), and Turbocharged Engines.

Use with ALL:  BlueTEC^®, Cummins^®, Duramax^®, EcoDiesel^®, Navistar^®, PowerStroke^®, TDI^® CleanDiesel and many more.

• Cleans Injectors, Valves and the Combustion Chamber
• Boosts Cetane, Power, Performance and Mileage
• Stabilizes Fuel, Lubricates and Protects
• Strong enough for Heavy-Duty Diesel engines, but packaged for easy no spill installation in Light / Medium Duty Diesel vehicles.
• Increases power, performance, kilometres per liter and saves fuel by lubricating the complete fuel system.  Safe to use on vehicles which have converters, DPF particular filters, or DEF systems.
• Helps eliminate black smoke, fuel gelling, clogged injectors, rough idle and hard starts. Works equally well in trucks, Ute’s, SUV’s and passenger car diesel applications.
• The 8,000 KM Complete Fuel System Tune-Up
• Cleaning and Protecting Engines Since 1921

Technical: 

• Heavy Duty Top-Lube improves fuel lubricity to protect fuel injectors and pumps from wear, especially in todays severely refined diesel fuels.
• Cold Flow Additives inhibit wax crystal growth, reducing fuel pour point and cold filter plug point even in harder to treat diesel fuels. Reduces CFPP up to 5°C (20°F).
• Fuel Stabilizer Antioxidant retards oxidation, reduces sludge formation, inhibits fuel decomposition and provides fuel stability for storage.
• Cetane Improver raises the Cetane number of diesel fuel to improve cold stars and reduce misfires, warm-up time, black exhaust smoke, and emissions. Typical numbers show a 1 to 2 point increase in Cetane Number CN per ASTM D613 engine test.
• New Generation Detergent is a multifunctional ashless dispersant additive improving the quality of diesel fuel. Dual clean-up and keep-clean formula removes injector deposits, prevents and restores lost power and improves fuel economy.  Real world testing shows an average fuel economy increase of 7.3% and an 87% power recovery from cleaning effects with regular use.

Note: 

This product includes a specially designed spout which allows it to be poured into all fuel tanks, include those with misfuelling devices.  Use anytime in a nearly full tank, or add to tank and then fill with up to 130 litres of diesel fuel.  For smaller tanks from 40 to 70 litres, use 1/2 bottle pouring equal amounts from each side.  Larger tanks use one bottle for every 110 litres of fuel.

This diesel fuel additive complies with the federal low sulfur content requirements for use in diesel motor vehicles and non-road engines.

Directions: 

Bend & twist spout and tear away on the perforated tab.  Remove cap and foil seal.  Tightly screw spout onto bottle.  Gently tip bottle and complete insert spout into fuel tank opening, allow entire contents to empty into tank.  For continued protection and cleaning, use one bottle every 8,000 km.  Results will either be immediate, or noticeable within a few days of driving.

To keep the system clean and lubricated in-between treatments, use Rislone Hy-per Fuel Injector Cleaner Upper Cylinder Lubricant part number 44701 (177 mL).

Rislone^® Hy-per Fuel™ Complete Fuel System Treatment improves the quality of petrol by increasing its cleaning ability, adding lubrication, removing contaminants, reducing spark knock, and helping to prevent the fuel from going bad.  This one dual cavity bottle contains the same amount of additives equal to a bottle of regular injector & complete fuel system cleaner, upper cylinder lubricant, fuel stabilizer & conditioner, petrol dryer, petrol treatment and octane booster. Simply put, it is the best all in one petrol fuel additive money can buy.

Works with ALL:  Fuel Injected, Port Fuel Injection (PFI), Direct Injected (DI / DIG), Petrol / Gasoline Turbo Direct Injected (GTDI), Turbocharged, LPG and Carbureted Engines.

Use with ALL:  Unleaded, Premium, and Ethanol (E10, E85) Flex Fuel Vehicles

• Cleans Injectors, Valves, Fuel Lines, Intake Manifold and the Combustion Chamber
• Boosts Octane, Power, Performance and Mileage (kilometers per litre)
• Stabilizes Gas, Lubricates and Protects
• Increases power, performance, mileage and saves fuel by cleaning & lubricating the complete fuel system. Engine dynamometer tests show improved fuel economy.
• Helps eliminate noisy injectors & fuel pumps, rough idle, hard starting and hesitation. Regular use provides reduced fuel system and emission control repairs.
• Will not void manufacture’s new vehicle warranty and safe to use on vehicles which have oxygen sensors and catalytic converters. Exceeds EPA compliance performance criteria and is EPA registered.
• The 8,000 km Complete Fuel System Tune-Up
• Cleaning and Protecting Engines Since 1921

Technical: 

• Upper Cylinder Lubricant (UCL) Top-Lube reduces friction and wear and improves fuel economy.
• Water Remover Petrol Dryer removes free water in petrol tank helping to prevent petrol line freeze-ups in the winter, and moisture related corrosion year round. This also works to reduce emissions and inhibits bacterial growth in petrol tanks.
• Fuel Stabilizer and Triple Corrosion Protection inhibits oxidation, gum, varnish and corrosion, helping petrol resist breakdown improving stability. Provides A-rating corrosion protection.
• Petrol Treatment Additives provide maximized power and acceleration, optimized fuel economy and excellent performance in petrol engines.
• Octane Booster raises the Octane number of petrol and Octane Requirement Increase (ORI) reduces spark knock, misfires and emissions.
• Premium P.E.A. Polyetheramine New Generation Detergent Patented Formula is a multifunctional additive improving the quality of petrol. Dual clean-up and keep-clean formula removes injector, combustion chamber and intake valve deposit which restores lost power and improves fuel economy.

Note: 

This product includes a specially designed spout which allows it to be poured into all petrol tanks, include those that use a capless (no fuel cap) system..  Use anytime in a nearly full tank, or add to tank and then fill with up to 70 litres of petrol.  For smaller tanks from 20 to 40 litres, use 1/2 bottle pouring equal amounts from each side.  Larger tanks use one bottle for every 60 litres of petrol.

Directions: 

Bend & twist spout and tear away on the perforated tab.  Remove cap and foil seal.  Tightly screw spout onto bottle.  (Pictured right)  Gently tip bottle and complete insert spout into petrol tank opening, allow entire contents to empty into tank.  For continued protection and cleaning, use one bottle every 8,000 km.  Results will either be immediate, or noticeable within 150 km of driving.

To keep the system clean and lubricated in-between treatments, use Rislone Hy-per Fuel Injector Cleaner Upper Cylinder Lubricant part number 44701 (177 mL) or 44732 (950 mL).

Rislone Gear Repair is a treatment additive for use with automotive, heavy duty, agricultural, marine and industrial gear oils.  Designed to mix with all synthetic and conventional petroleum GL-4, GL-5, MT-1 gear oil grades including 75W-90, 80W-90, 75W-140, 85W-140 and all others.

Extends system life by stopping leaks, reducing noise and improving gear performance.  Superior anti-wear, anti-foam and anti-corrosion protection.

Works in all manual gearboxes, differentials, open & posi axles and more.  Stops pinion, axle, output shaft and other seal leaks.  Reduces grinding, whining, clunking and protects gears.

• Seal Conditioner stops current and prevents future leaks by protecting and reconditioning seals.

• Extreme Pressure EP / Anti-wear AW Agents provide excellent metal-to-metal wear protection reducing noise and gear temperatures. These Sulfur, Nitrogen and Phosphorus additives meet the requirements of API GL-4 and GL-5 specifications.

• Friction Modifier supplements EP / AW additives to help reduce noise and wear. This helps shifting in a manual transmission and also stops chatter in limited slip posi traction axles.   .

• Performance Additive Booster including tackifier and highly sheer stable multigrade viscosity modifiers work to keep oil on the gears and bearings where it can better lubricate, especially at higher temperatures. Pour Point Depressant allows product to flow even at low temps.

These additives stop & seal oil leaks and reduce noise. Gear Repair renews worn oil and restores older & high mileage / kilometre gear performance.  Works and safe to use on differential axles (limited slip, posi, open, electric), gears (hypoid, spider, worm, rack), transfer case (AWD, 4WD, gear oil, ATF), manual standard transmission (gear oil, engine oil, ATF), hubs, marine and much more.  Helps with small leaks (if you need to add oil 1x per month), medium leaks (If you need to add oil 1x per week), and other oil related problems.

INSTRUCTIONS

Add 150mL to 175mL per litre of system capacity.  Do not overfill.  One bottle treats up to 3 litres of gear oil.  Can be added to top-off existing low fluid level, or when changing oil.  Results will be immediate, or noticeable within 150 kilometres, or 2 days of driving.  If leaks or noise continues, second application may be required or mechanical attention is needed.

Safe To Use On:

Agricultural and Farm

Automotive

Construction Equipment

Factories

Forestry

Industrial Systems

Machine Shops

Marine

Mining

Power Sports

Trucking and Heavy Duty

Waste Management

Works On:

ATV, UTV

Boats

Cars

Dump Trucks

Earth Mover

Lawn Equipment

Machinery

Motorcycle

Race Cars

Tractors

Trailers

Trucks

Repairs:

Front or Rear Axle

Gear Box / Case

Gear Reduction Units

Hubs

Lower Drive Unit

Manual Transmission

O-ring Boss Hose Fittings

Power Take Off PTO

Seals and O-rings

Transfer Case

Worn Gears

Other Gear Systems

Automatic Transmissions do not work without fluid, nor do they work well without the correct fluid.  Automatic Transmission Fluid (ATF) is one of the most complex of all lubricating fluids.  It has to reduce friction enough to prevent wear and control temperature while at the same time allowing some friction to prevent the internal clutch material from slipping.  This same fluid must operate at low and high temperature extremes. Rislone Transmission Stop Slip with Leak Repair contains a special blend of viscosity improvers, anti-wear friction modifiers and extreme pressure performance additives to solve most transmission problems.  These additives reduce rough shifting and friction, while eliminating slip, controlling temperature, and repairing shudder, chatter and whining.  Excellent to use as a preventative maintenance product.  Use to top off existing fluid when low  or add a bottle when changing fluid.  Specifically designed for higher kilometre / mileage vehicles over 100,000 kilometres.

• Performance additives restore bands & clutches to stop slip, eliminate hesitation and reduce rough shifting.
• Renews and stabilizes automatic transmission fluid (ATF) reducing noise, shudder and chatter.
• Perfect additive for poorly maintained transmissions.
• Premium formula restores transmission performance and saves on costly transmission / transaxle repairs.
• Stops fluid loss, reduces friction & wear, and protects internal components.
• Lowers operating temperature, the number one cause of transmission failure.
• Works with any front wheel drive, rear wheel drive, all-wheel drive and four wheel drive automatic transmission. Do not use in CVT transmission.
• Use in ALL light duty and heavy duty vehicles including; car, truck, van, Utes, SUV, and RV’s with any 3 speed, 4 speed, 5 speed, 6 speed, electronic, overdrive, automatic or manual transmission. On manual transmissions it will only help with leaks, noise and hard or loose shifting, but not slipping.

Compatible with ALL types of domestic and import transmission fluid; including petroleum and synthetic formulas.

INSTRUCTIONS:

Automatic Transmission (Adding to Existing Fluid)

Remove transmission dipstick and check fluid level.  For most vehicles this is usually done while the engine is running and the transmission is in Park.  Tip:  The transmission dipstick is usually located near the engine oil dipstick, but further back into the engine compartment. Some vehicles do not have a normal dipstick.  For those, the product has to be added to the transmission through a fill plug.  Consult owner’s manual for location. If fluid is low, pour entire contents of the bottle into the dipstick tube.  Do NOT overfill.  For compact and smaller vehicles, use ½ of the bottle.  Tip.  If necessary, to prevent overfill, drain some fluid from transmission.  Check fluid level again.  Top off with manufacturer’s recommended transmission fluid as needed. Replace dipstick and drive 10 to 15 minutes to circulate fluid. Depending on transmission problem, results will either be immediate or noticeable within a few days of driving. In transmissions with seriously damaged components a second treatment may be required.  In this case, it is suggested that the transmission fluid and filter be changed and a second application of Rislone Transmission Stop Slip be added.

Automatic Transmission (Changing Fluid)

If using Rislone Transmission Stop Slip when changing transmission fluid, add entire contents of bottle after filter is changed.  Then refill with manufacturer’s recommended fluid to proper level.  Drive vehicle and recheck fluid level.

Manual Transmission:

May be used in manual / standard “stick” transmissions to top off the fluid level to stop leaks, noise and grinding gears.

DOSAGE:

One bottle will treat 11 to 15 litres of transmission fluid.  For compact and smaller vehicles, use ½ of the bottle.  Do not overfill.

For severe problems or badly worn transmissions, use double the dosage or a second bottle.

Modern hydraulic systems work under extreme conditions and this can be compounded from leaks requiring continual topping-off of fluid, not to mention running the system low, which can also increase the fluid temperature, causing system damage.  Unscheduled maintenance from leaks, including checking fluid level, adding fluids, or repairing leaks costs time and money.  Also, you have the environmental impact of all that fluid leaking on the ground, or into the water.

Hydraulic Seal contains a premium high quality durable field proven zinc based additive package along with viscosity modifiers to restore thermal stability and anti-wear additives in the hydraulic system. This additive package has been tested to provide excellent results in Group I, II and III OEM & aftermarket hydraulic petroleum and synthetic fluids.  Reduced wear also reduces contamination, heat and downtime, while also improving equipment and fluid life.  Additional rust and oxidation inhibitors provide stability improvements which reduces the formation of sludge, varnish and acids keeping the system clean extending service life.  Can be used in tractor or equipment with wet brake systems.  CAUTION: Do not use in DOT 3, 4, 5 hydraulic brake systems.

Multi-grade, multi-viscosity, multi-functional formulation is designed and approved to work in a wide range of climates with multiple hydraulic oil grades including ISO22, ISO32, ISO46, ISO68, ISO100 and others.  Special concentrated formulation does not thicken hydraulic fluid so current oil stays in grade, optimizing all-weather performance.   Maintains fluid viscosity even at higher temperatures stabilizing hydraulic pressure.

Shear Stable Polymer additive and viscosity modifiers help keep higher hour and worn systems lubricated during operation and extended shut down times.

High flash point non-silicone type foam inhibitor provides superior foam inhibition to ensure smooth efficient operation and proper system lubrication.  Good solubility characteristics will not negatively impact air entrainment.

Pour point depressant is designed to allow proper fluid flow in all temperature ranges.

Seal conditioners recondition and restore hard, brittle, shrunken and worn out seals, o-rings and gaskets reducing fluid leaks during operation. These additives work on both internal and external leaks.  This same additive works to protect seals and prevent seals that contact the hydraulic fluid from shrinking and hardening.  Chemical polymers work where other stop leaks fail to seal leaks that are caused by normal usage. This includes small wear grooves and pits in the shafts. The polymer forms a film between the seal and the shaft, helping to preventing leaks.  Hydraulic Seal works on many elastomer types including polyacrylate elastomers like n-butyl acrylate and Nitrile Rubber (NBR Nitrile Butadiene Rubber, Buna-N).

Developed for both low and high pressure hydraulic systems in industrial and mobile applications.

Save To Use On:

Agricultural and Farm

Construction Equipment

Factories

Forestry

Industrial Systems

Machine Tools and Presses

Marine

Mining

Waste Management

Leaks

Works On:

Dump Trucks

Earth Movers and Excavators

Loaders

Forklifts

Refuse

Tractors

Hydraulic Elevators, Hoists and Lifts

Jacks

Snow Plows

Repairs:

Pump Seals

Control Valves Seals

Actuators

Rams

Cylinders

O-ring Boss Hose Fittings

Hydrostatic Transmissions

Seals and O-rings

Other Hydraulic Fluid

Features:

Demulsifiable Detergents

High Dielectric Strength

Benefits:

Superior Rust and Yellow Metal Corrosion Protection

Anti-foam Protection

Good Low Temperature Flow Properties

Outstanding hydrolytic, oxidative and thermal stability

Exceptional Wet and Dry Filterability

Excellent shear stability and stay-in-grade performance

Instructions For Use

1) Check level of hydraulic fluid when system is at normal operating temperature.

2) Add the correct amount of product per dosage chart.  Do not overfill.

3) Run equipment for at least 15 minutes to mix thoroughly with fluid and activate product to start working.

4) Check hydraulic fluid level to see if leak has stopped.  Old accumulation of fluid on outside of system may drip for a few days after leak has stopped.

5) Most leaks are sealed within a few hours of application and usage.  If leak continues, mechanical attention is needed and replacement of seals may be required.

Dosage

Normal—Add 30mL of Rislone Hydraulic Seal for every liter of hydraulic fluid capacity.

Worn—In extremely worn systems use up to 60mL per liter of fluid capacity.

Preventative—For preventative maintenance, use 15mL per liter of fluid capacity.

Rislone^® Jack Oil with Stop Leak is specially designed to stop seal and o-ring leaks caused by normal jack wear and age.  If you are having to add oil to your jack, it has a leak.  Easy fill cap is great for topping fluid off.

Brings life back to old jacks and prevents leaks & seepage on newer jacks.  Premium formulation reconditions seals to stop current and prevent future leaks.

World’s Most Trusted Stop Leak Brand Since 1921

Mixes All Approved Hydraulic Jack Oils

Safe and Easy to Use

Contains Anti-Wear & Oil Stabilizer

Non-Corrosive, Non-Clogging & Non-Foaming

Works in All Floor, Trolley and Bottle Jacks

Also Works With All Snow Plow Fluids

INSTRUCTIONS:

Clean area around filler cap.  Fill jack to proper level.  Do not overfill.  Cycle jack by lifting and releasing a few times to release any air caught in system.  Leaks usually stop in a few days of normal use.  If leak continues, repair may be required.

DOSAGE:

One bottle treats 1 to 2 litres of oil. For larger systems use one bottle for every 2 litres of oil capacity.

CAUTION:

Do not use in hydraulic brake systems.