LOCATION: PUERTO RICO

Rislone Block Seal Head Gasket Sealant is scientifically formulated to permanently seal coolant leaks that are the cause of most overheating problems. For most vehicles, this is the last chance before going to a junk yard or paying an expensive repair bill. This product contains a blend of aramid and refractory fibers giving the strength of a bullet proof vest and the heat resistance of fire-proof clothing. As these particles penetrate a crack or the blown head gasket area, they lock together and bond forming a hard permanent ceramic type seal. Your vehicle is a good candidate for this product if it can idle for 20 minutes without overheating or having to add coolant. Works effectively on cast iron or aluminum blocks & heads. Detailed instructions on back booklet label take you through each step of using the product.

• World’s Most Trusted Stop Leak Brand Since 1921 
• Stops All Coolant Leaks
• Seals Block Leaks, Blown Head Gaskets, Cracked Heads and Other Hard to Stop Coolant Leaks
• Dual Action 2 Part Formula—Twice the performance
  LIQUID CERAMIC
  Liquid penetrates large and small leaks to form a seal actually harder than the original head gasket.
  REINFORCED FIBERS
  Fiber additives lock together with liquid to increase strength and promote a permanent seal.
• Only Add to Radiator After Removing Antifreeze

Overheating can be caused by a blown head gasket, cracked head or leaking block. Rislone Block Seal Head Gasket Sealant eliminates this problem. In addition, overheating can be caused by a stuck thermostat, bad water pump or defective radiator cap. If at any time the engine overheats, turn vehicle off and allow engine to cool. Make sure these cooling system parts are in good working order before using Rislone Block Seal Head Gasket Sealant. When one of these parts fails, it can cause the head gasket to fail.

WARNING:
Head Gasket Sealant is NOT COMPATIBLE with antifreeze and must only be added to the cooling system after ALL ANTIFREEZE has been flushed and removed.

DANGER:
Opening the cooling system while engine is hot or running may cause severe burns.

DISPOSAL:
Observe local laws & regulations. Where permitted, dispose of in sanitary sewer system. Never pour on the ground or in a storm sewer system.

NOTE:
Protect from freezing.

INSTRUCTIONS:

1. Engine must be cool enough to safely open the radiator cap. (This could take 30 minutes or longer). Drain and completely flush antifreeze from cooling system and overflow tank. Using a flush “T” with garden hose works best. If cooling system is dirty, use a good quality flush following manufacturer’s instructions. ALL antifreeze must be removed or clogging may occur.
2. Shake well, Mix Head Gasket Sealant in a bucket or container with approximately 3 litres of warm water. Pour this mixture directly into the radiator. If using in a small cooling system, including all 4 cylinder engines, mix ½ bottle of the Head Gasket Sealant with the warm water.
   TIP: If you do not have access to your radiator and vehicle has a pressurized reservoir, then product can be added to reservoir. If not then remove top hose where it connects to the top of radiator and install product in hose. Reattach and tighten clamp.
3. Fill cooling system with water and reinstall radiator cap.
4. Start engine, turn heater on hot and fan on high.
5. Run engine for 10 minutes or until thermostat opens.
6. Turn vehicle off and allow engine to cool. Allow enough time so it is safe to open cap.
7. Top off (fill up) cooling system with water and reinstall radiator cap.
8. Run engine at idle until normal operating temperature is reached. Continue running engine at idle for 15 minutes.
9. Turn vehicle off and allow 45 minutes to cool.
10. Top off cooling system with water as needed and reinstall radiator cap.
11. Run engine at idle until normal operating temperature is reached. Continue running engine, but at high idle (approximately 1200 RPM’s for vehicles with a tachometer) for 20 minutes.
12. Turn vehicle off and allow engine to cool for 1 hour.
    TIP: For vehicles with intermittent or very minor leaks, it is recommended to follow step 12 by idling vehicle for one hour.
13. Remove radiator cap and drain system.
14. Leave drain open and radiator cap off for 12 to 24 hours. If temperature is below freezing, vehicle must either be kept heated or immediately go to step 15.
15. Flush entire cooling system and refill with manufacturer’s recommended antifreeze / water mixture.

DOSAGE:
One bottle treats cooling systems from 7.5 to 19 litres. Use 1/2 bottle for cooling systems from 4 to 7.5 litres.
For larger systems, use 1 bottle for every 19 litres of cooling system capacity.

Rislone High Mileage / Kilometer Cooling System Repair has twice the performance of other products, by not only stopping cooling system leaks, but adding future protection. It is scientifically formulated to stop coolant leaks, thereby reducing antifreeze loss, while correcting other cooling system problems helping to prevent costly repairs and breakdowns. In addition, Cooling System Repair contains Xtreme Cool™ which stops overheating and reduces water temperature. Works on all vehicles and in any gasoline, turbocharged and diesel engines. Use with ALL 50-50 mix types and colors of antifreeze coolant and / or water. For most vehicles leaks stop instantly. For many vehicles, this is your last change before paying an expensive repair bill or replacing the vehicle.

World’s Most Trusted Repair Brand Since 1921

Dual Action Formula—Twice the performance

Safe And Easy To Use

Xtreme Cool – reduces the surface tension of coolant increasing the wetting ability. This improves heat transfer reducing coolant temperature helping to prevent overheating and leaks.

Guaranteed To Seal & Stop Leaks Plus…
Reduces—Antifreeze loss, temperature and costly breakdowns.

• Water Pump Lube
• Corrosion Inhibitors
• Heat Transfer Agent

Stops—Coolant leaks, overheating and other cooling system problems.

• Carbon Fiber Sealer
• Leak Sealing Liquid
• Stop Leak Treatment

The result is reduced coolant temperature and no antifreeze loss, leaks or overheating.

DANGER: Opening the cooling system while the engine is hot or running may cause severe burns.

NOTE: Cooling systems that are dirty or partially clogged should be flushed before usage.

Protect from freezing.

INSTRUCTIONS:
Install only in a cold engine. Shake well. Pour entire contents of the 2-chamber bottle directly into the radiator. If direct access to radiator is not available, install in reservoir / overflow tank. Fill radiator overflow tank to proper level and reinstall cap. Drive/idle engine for 15 minutes. If leak continues, second application may be required or mechanical attention is needed. Leave Cooling System Repair in cooling system for continued protection. Depending on the cooling system problem, results will either be immediate or noticeable within (2) days or 150 km of driving.

DOSAGE:
One bottle is designed to treat 6 liters to 15 liters of coolant capacity, which is the normal size for most vehicles. On smaller systems under 5.9 liters, only use half bottle, pouring equal amounts from each side. For larger systems use one bottle for every 15 liters of cooling system capacity.

WHAT IS YOUR COOLING SYSTEM PROBLEM?
Small Leaks—Need to add fluid 1X per week
Medium Leaks—Need to add fluid 1X per day
Leaks—Radiator and heater core leaks
Overheating—Contains Xtreme Cool
Noise—Water pump lubricant
High Mileage Vehicle

WE CAN HELP!!!
      Safe For— Domestic / Import, Cars, Trucks, Vans and SUV’s
      Engines—Gas, Diesel and Turbocharged
      Coolant—Works with all types and colors of antifreeze coolant, or water

Rislone® Hy-per Cool™ Radiator Cleaner & Super Flush will help your cooling system by removing deposits that build up over time causing overheating. Heavy duty formulation is specially designed to clean solder bloom, oily residue, rust and scale. Contains water pump lubricant and corrosion inhibitors, so will not damage the pump like other brands.

• Fast, easy and safe to use in all cooling system materials, including plastic and aluminum. Works with all cooling systems.
• Eliminates damaging coolant deposits, reducing engine operating temperature to prevent overheating.
• Neutralizes acids that cause corrosion and helps prevent formation of future scale deposits.
• Heavy Duty Xtreme Clean™ formula cleans entire cooling system.
• Removes deposits and coolant gel for a complete cleaning in 30 minutes or less.
• Use every time changing coolant for light flushing or heavy duty cleaning.
• Clean systems run cooler

Caution:
Never remove radiator cap if engine is hot.

Dosage:
One bottle treats up to 15 liter systems.

Directions:
Step 1. With engine off and cool, drain system.
Step 2. Close drain and add entire contents of bottle, then refill system with water. Reinstall cap, start engine, turn heat on high, and run engine for 10 to 15 minutes. Turn engine off and allow to cool, drain system.
Step 3. Flush cooling system and reservoir until water runs clear.
TIP: Using a flush “T” with garden hose works best for final cleaning.
Step 4. Refill cooling system and reservoir with manufacturer’s recommended antifreeze/water mixture.

For best results add Rislone Hy-per Cool Super Coolant after flushing the system, as the metal surfaces inside the system are now cleaned and primed for optimal heat transfer performance and corrosion protection.

Disposal
Observe local laws and regulations. Where permitted, dispose of in a sanitary sewer system. Never pour on the ground or in a storm sewer system.

Rislone® Hy-per Cool™ Super Coolant contains very high cloud point surfactants designed to provide maximum wetting (coolant surface tension reduction) at normal and high cooling system operating temperatures. This supercharged coolant mixture eliminates bubbles, resulting in improved heat transfer to dissipate heat more efficiently in the entire cooling system. Real world and laboratory testing shows reduced engine temperatures by up to 17°C helping to prevent overheating. Super Coolant lubricates and protects the water pump, and helps prevent corrosion, erosion and electrolysis of all parts of the cooling system, including aluminum, plastics, rubber and more. Works with all colors and types of antifreeze coolant including extended life, or straight water.

Provides extra protection against higher engine temperatures. Up to 41°C lower cylinder head temperatures (CHT) enhance engine efficiency, proving better fuel economy, power and performance.

Use in gasoline classic cars, hot rods, trucks, RV’s, motorcycles, automotive, heavy duty, diesel, powersports ATV, off road, racing, towing and most anything else with a cooling system.

Racing approved and safe to use from drag strips to the oval track. Contains no glycol. Provides no antifreeze protection. Always check for freeze protection if needed.

• The Best Coolant Additive Money Can Buy
• Reduces Engine Temperature
• Prevents Overheating
• Provides Maximum Corrosion Protection
• Supercharges Cooling System Performance

Caution:

Never remove radiator cap if engine is hot.

Directions:
Add one bottle to treat 11.5 to 19 liter systems. For larger and smaller systems add 30 mL per liter of capacity. Can be added to overflow tank, but it will take 4 to 5 heating and cooling cycles for product to fully enter the system. For continued protection re-treat once per year, and every time changing coolant.

Rislone® Radiator Stop Leak Sealer is specially designed to stop minor cooling system leaks and drips caused by normal cooling system wear and age.

Works with ALL Types and Colors of Antifreeze Coolant and / or Water

Stops & Seals Coolant Leaks

Seals Leaks in Radiators, Gaskets, Heater Cores & Freeze Plugs

DANGER: Opening the cooling system while the engine is hot or running may cause severe burns.

NOTE: Cooling systems that are dirty or partially clogged should be flushed before usage.

Protect from freezing.

INSTRUCTIONS:
Shake well. Pour Stop Leak into a cool radiator. If direct access to radiator is not available, install in overflow / reservoir tank. Fill radiator and overflow tank to proper level and reinstall cap. Drive / idle engine for 15 to 30 minutes. If leak continues, a second application may be required, or mechanical attention is needed. Leave Rislone in the cooling system for continued protection.

DOSAGE:
Passenger cars and light trucks—Use one bottle for 6 & 8 cylinders and half bottle for 4 cylinder engines. Small engines or other small systems use approximately 20 mL per liter of fluid capacity.

Over the road and heavy-duty equipment—Install one bottle for every 15 liters of coolant
capacity.

Rislone® Hy-per Cool™ Xtreme Clean™ Radiator Cleaner will help your cooling system by removing deposits that build up over time causing overheating. Heavy duty formulation is specially designed to clean solder bloom, oily residue, rust and scale. Harmless to all parts of the cooling system, including copper and aluminum. Non-acid formula is safe to use on all cooling system materials.

• Heavy Duty Xtreme Clean™ formula cleans entire cooling system.
• Use every time changing coolant for light flushing or heavy duty cleaning.

Caution:
Never remove radiator cap if engine is hot.

Dosage:
One bottle treats up to 15 liter systems.

Directions:
1. Allow the engine to cool. Drain the system. Close the drain.
2. Pour the entire contents of the bottle and refill the system with water. For large cooling systems, use one bottle of Radiator Cleaner for every 12 liters. Replace the cap.
3. Start the engine. After reaching the normal operating temperature keep it running for 10 minutes with the heating on at maximum.
4. Allow the engine to cool. Drain the cooling system and flush the overflow tank until the water runs completely clear.
5. Close the drain. Refill the cooling system and the overflow tank with the manufactures recommended antifreeze coolant / water mixture.

Disposal
Observe local laws and regulations. Where permitted, dispose of in a sanitary sewer system. Never pour on the ground or in a storm sewer system.

Rislone® Jack Oil with Stop Leak is specially designed to stop seal and o-ring leaks caused by normal jack wear and age. If you are having to add oil to your jack, it has a leak. Easy fill cap is great for topping fluid off.

Brings life back to old jacks and prevents leaks & seepage on newer jacks. Premium formulation reconditions seals to stop current and prevent future leaks.

WORKS ON ALL:
Bottle Jacks
Floor Jacks
Lifts & Rams
Shocks

Mixes All Approved Hydraulic Jack Oils
Safe and Easy to Use
Contains Anti-Wear & Oil Stabilizer
Non-Corrosive, Non-Clogging & Non-Foaming
World’s Most Trusted Stop Leak Brand Since 1921

INSTRUCTIONS:
Clean area around filler cap. Fill jack to proper level. Do not overfill. Cycle jack by lifting and releasing a few times to release any air caught in system. Leaks usually stop in a few days of normal use. If leak continues, repair may be required.

DOSAGE:
One bottle treats 1.5 to 2.5 litres of oil. For larger systems use one bottle for every 2 litres of oil capacity.

CAUTION:
Do not use in hydraulic brake systems.

Rislone® High Kilometre / Mileage Compression Repair with Ring Seal is a concentrated proprietary blend of high-shear and premium polymers developed for higher mileage engines that are suffering from decreased or uneven compression. Low compression can be caused by normal engine wear and decreased sealing between the piston rings and cylinder walls. The non-dispersant olefin copolymers fill scratches & grooves in cylinder walls to increase and stabilize compression in all cylinders. Compression Repair renews worn engines, rebuilds compression, restores lost power and repairs engine blow-by. In addition, Compression Repair helps vehicles pass emission tests.

Some signs of decreased compression include loss of power, poor fuel economy, oil consumption, blue smoke from exhaust, plug fouling and engine noise or vibration.

The Viscosity Improver (VI) is designed specifically to provide an optimum balance of shear stability and thickening efficiency required in old and modern engines. This performance additive meets the most severe passenger car and truck engine requirements.

Product works by freeing sticky rings and filling gaps & scratches in cylinder walls, eliminating blow-by and compression loss while also reducing friction and wear. Blow-by is usually caused by gaps in internal engine parts resulting from excess wear.

Rislone Compression Repair with Ring Seal does not contain any harmful lead or other metals that could damage the inside of your engine or be burned and contaminate emissions components and the environment.

Works on gasoline and diesel engines with conventional, high kilometre and synthetic engine oils.

INSTRUCTIONS:
Add entire bottle of COMPRESSION REPAIR WITH RING SEAL to engine crankcase at or between oil changes. Do not overfill. Results will either be immediate or noticeable within a few days of driving. Install Compression Repair every 10 000 km or with every oil change.

DOSAGE:
One bottle treats 4 to 6 litres of oil. For larger engines, use one bottle for every 5 litres of capacity. On 4-Stroke ATV, Motorcycle and small engines, including wet clutch applications, use approximately 100 mL per litre of oil capacity.

The common element between all of the engine components is the oil. Oil is the lifeblood of the engine and is pumped under pressure to all the moving parts. The two main parts needing oil for lubrication are the bearings and pistons. As the engine ages and gains more kilometres, the oil alone can’t do the job. Internally, parts don’t fit as tightly as they originally did, which causes noise and loss of power. Bearings wear down, seals leak, lifters tick, blow-by passes around tired rings, and power is lost. When installed, Engine Repair helps to stop and prevent these problems and will also extend the useful life of your engine. Engine oils are generally used to reduce friction between moving parts. In addition to lubricating, motor oil must cool, provide corrosion protection and be a method of removing contaminants. As lubricants degrade, their properties change, leading to increased friction and wear. Over time the natural wear that occurs inside the engine causes reduced oil pressure, loss of compression (power loss), lower fuel efficiency, oil consumption (leaks & smoking) and noise (knocking & ticking). When installed, Rislone High Mileage Engine Repair helps to stop and prevent these problems and enhances the useful life of your Engine. The result is improved compression,
horsepower and increased performance.

INSTRUCTIONS:
Adding to existing Engine Oil
Remove engine dipstick and check oil level. If oil is low, remove oil cap and install entire contents of the two-chamber bottle into engine crankcase. Do not overfill. Top off with manufacturers recommended engine oil as needed. Reinstall dipstick and oil cap. Drive/ idle engine for 10-15 minutes.

Depending on the engine problem, results will either be immediate or noticeable within two days or 150 km of driving. In engines with seriously damaged components, a second treatment may be required. In this case, it is suggested that the oil and filter be changed, and a second application of Engine Repair be added.

Changing Oil
If using Engine Repair when changing oil, add entire contents of bottle after filter is changed. Then refill with manufacturer’s recommended oil to proper level. Drive vehicle and recheck oil level.

DOSAGE:
One bottle is designed to treat 4 to 6 litres of oil, which is the normal size for most vehicles. On smaller systems from 2 to 3.9 litres, only use half bottle, pouring equal amounts from each side. For larger systems use one bottle for every 5 litres of capacity.

WHAT IS YOUR ENGINE PROBLEM?
Small Leaks—Need to add oil 1X per month
Medium Leaks—Need to add oil 1X per week
Leaks—Seals and Gaskets
Noise—Knocking or Ticking
Smoking– Blue Exhaust Smoke
Low Compression—Reduced Power
Worn Engine Parts
High Mileage / High Kilometre

WE CAN HELP!!!
Safe For— Domestic / Import, Cars, Utes, Trucks, Vans and SUV’s
Oil—Regular Petroleum, High Mileage, Synthetic Blends and Full Synthetic Oils
Use On– Gasoline, Diesel and Turbocharged Engines
Works On—3, 4, 5, 6, 8 and 10 Cylinder Engines

WHAT IS AN ENGINE?
There are two basic types of engines:
Gasoline Engine – most cars’ & light duty trucks – The most popular engine runs on a mixture of        petrol and air. The air & fuel is compressed (squeezed) and then ignited by a spark to move the          piston, which in turn allows the vehicle to move.
Diesel Fuel Engine – some cars’ & most heavy duty trucks – The second most popular engine          runs on a mixture of diesel fuel and air. Instead of spark, it uses the high temperature caused by          extreme compression of the air & fuel mixture to move the piston.
Works on ALL Engines
Gas, Diesel, Hybrid and Turbo

Engine Components
Automotive engines are a combination of mechanical, hydraulic and electric parts.
Mechanical
Many mechanical parts are required to operate an engine. Some of the more important parts are        the oil pump, crankshaft, bearings, seals, piston rings, lifters and valves.
Hydraulic
The hydraulic system uses the oil pump to create pressure which lubricates internal engine parts        and helps to operate the lifters and cam phasers.
Electrical
The most common electrical parts include the spark plugs, fuel injectors, computer and many              sensors.

Rislone® Engine Oil Stop Leak Concentrate is specially designed to stop seal and gasket leaks caused by normal engine wear and age.

Works with ALL gasoline and diesel engines using conventional, high kilometer / mileage and synthetic engine oil.

World’s Most Trusted Stop Leak Brand Since 1921

Stops and Seals Motor Oil Leaks

Safe and Easy to Use

Restores Gaskets & Seals to Stop & Prevent Engine Oil Leaks

INSTRUCTIONS:
Add entire bottle of stop leak to engine oil at or between oil changes. Leaks usually stop in 300 km or 3 days of driving. If leak continues, a second application may be required or mechanical attention is needed.

DOSAGE:
One bottle treats up to 5 liters of oil. For larger systems use 1 bottle for every 5 liters of oil capacity. On small 4 cycle engines, use approximately 65 mL per liter of capacity.

Rislone® Engine Treatment is high quality penetrating lubrication oil, combined with protective engine additives and special cleaning agents. Its multi-grade formula allows the oil to flow freely and provides protection over a broader temperature range. Sludge and other harmful deposits within engines can alter tolerances, stick rings, cause noisy valves & lifters, and plug oil passages and screens. The unique Rislone formula is designed to penetrate into bearing surfaces, piston rings and ring grooves, where sludge and varnish is likely to form. These deposits are gradually removed and held in suspension until they are trapped in the filter or removed with the next oil change. Regular use of Rislone Engine Treatment, with oil and filter changes at the proper intervals, will keep such deposits to a minimum. A cleaner engine is a better lubricated engine with less friction & wear.

Works on gasoline and diesel engines with conventional, high kilometer / mileage and synthetic engine oils.

         PROTECTING ENGINES SINCE 1921
         REDUCES FRICTION AND WEAR
         QUIETS NOISY LIFTERS AND VALVES
         REMOVES & PREVENTS SLUDGE
         MAXIMIZES ENGINE POWER

INSTRUCTIONS: (Automotive Applications)
Adding To Existing Engine Oil—Remove engine dipstick and check oil level. If oil is low, remove oil cap and install entire contents of bottle. Do NOT overfill. Reinstall dipstick and oil cap.
When Changing Oil—If using when changing oil, replace 946 mL of your motor oil with Rislone Engine Treatment.
For best protection, use Rislone Engine Treatment at every oil change.

DOSAGE:
In passenger car and light truck engines, use one bottle for a 4 to 6 liter system.

For larger systems, stationary engines and diesel trucks, use at 20% of crankcase capacity.

For severely dirty engines, use two liters of Rislone Engine Treatment and change the oil after 150
kilometers of driving.

Rislone® One Seal™ multipurpose stop leak effectively seals all minor engine oil, transmission and power steering system leaks. It’s specifically designed to stop seal and gasket leaks caused by normal wear and age.

3X Sealer

Works with ALL Engine Oil, Transmission Fluid and Power Steering Fluids

Safe and Easy to Use

World’s Most Trusted Stop Leak Brand Since 1921

WARNING:
Do not use in the brake system or add to antifreeze / coolant.

INSTRUCTIONS:
Add entire bottle of One Seal to specific leaking system reservoir.

DOSAGE:
One bottle will treat one engine oil, transmission fluid or power steering fluid system leak. Leaks
usually stop in 300 km, or 3 days of driving. If leak continues, a second application may be required or mechanical attention is needed.

Rislone® Ring Seal® Smoke Repair is formulated to help stop blue exhaust smoke, reduce oil burning and prevent plug fouling caused from “blow-by”. Blow-by is usually caused by gaps in internal engine parts resulting from excess wear. Ring Seal contains high-shear polymers which provide a seal for worn pistons and rings to stop blow-by.

High kilometre / mileage formula is specifically designed for older higher kilometre engines. Viscosity improver cushions and coats engine parts helping to reduce wear and quiet noisy engines.  All weather formula retains oil flow characteristic in hot and cold weather.

Works on gasoline and diesel engines with conventional, high kilometre and synthetic engine oils. Can be added anytime, top off oil when low or while changing oil.

Protecting Engines Since 1921

Stops Blue Exhaust Smoke and Reduces Oil Burning

Seals Worn Pistons & Rings

High-Kilometre Formula

INSTRUCTIONS:
Add entire bottle of Ring Seal Smoke Repair to engine crankcase at or between oil changes. Idle or drive engine for 5 minutes after installation. Add Ring Seal Smoke Repair every 3500 km or with every oil change. If smoke continues, second application may be required or mechanical attention is needed.

DOSAGE:
One bottle treats 4 to 6 litres of oil for regular 4, 6 and 8 cylinder engines. For larger engines, use one bottle for every 5 litres of capacity. On 4-Stroke ATV, Motorcycle and small engines, including wet clutch applications, use approximately 89 mL per liter of oil capacity.

Rislone® Smoke Eliminator with Stop Leak is formulated to help stop blue exhaust smoke, reduce oil burning, seal oil leaks and prevent plug fouling caused from “blow-by”. Blow-by is usually caused by gaps in internal engine parts resulting from excess wear. Smoke Eliminator contains high-shear polymers which provide a seal for worn pistons and rings to stop blow-by.

Oil treatment viscosity improver cushions and coats engine parts helping to reduce wear and quiet noisy engines. All weather formula retains oil flow characteristic in hot and cold weather. Smoke Eliminator helps your engine last longer and makes your oil stronger.

Helps stop leaks caused by drying, hardening or shrinking of engine gaskets and oil seals.

Works on gasoline and diesel engines with conventional, high kilometre and synthetic engine oils.

Protecting Engines Since 1921
Stops Blue Exhaust Smoke and Oil Leaks
Seals Worn Pistons & Rings
3X Action Formula

Rislone Smoke Eliminator with Stop Leak will help relieve smoking caused from oil leaks, oil burning, worn & dry seals and blow-by.

INSTRUCTIONS:
Add entire bottle of Smoke Eliminator with Stop Leak to engine crankcase at or between oil changes. Idle or drive engine for 5 minutes after installation. Add Ring Seal Smoke Repair every 3500 km or with every oil change. If smoke or leaks continue, second application may be required or mechanical attention is needed.

DOSAGE:
One bottle treats 4 to 6 litres of oil for regular 4, 6 and 8 cylinder engines. For larger engines, use one bottle for every 5 litres of capacity. On 4-Stroke ATV, Motorcycle and small engines, including wet clutch applications, use approximately 100 mL per liter of oil capacity.

Rislone Super Leak Fix is formulated to work in multiple systems including all Engine Oil, Transmission, Power Steering, Hydraulic and Differential & Gear. Use to stop current leaks, or as a
preventative maintenance before leaks start. Premium seal renewing additives are designed to stop seal and gasket leaks caused by normal wear and age. Contains no solids, will not clog filter or harm system.

•  World’s Most Trusted Stop Leak Brand Since 1921
•  Multi-System Formula / 5X Sealer
      Engine
      Transmission
      Power Steering
      Hydraulic
      Gear & Axle
• Safe and Easy To Use / Will Not Harm Seals
• Spout / Hose Included for Easier Application

Helps with small leaks (if you need to add fluid 1x per month), medium leaks (If you need to add fluid 1x per week), preventative maintenance (to prevent future leaks from happening) with engine oil (gasoline, hybrid, diesel), transmission fluid (automatic, manual, CVT), power steering fluid (pump, gear box, rack & pinion), hydraulic (jack, snow plow, tractor, construction), and gear (differential, axle, gearbox, transfer case).

Instructions For Use
Fill hose included for easier application in some vehicles. Shake well. Add Super Leak Fix to leaking system per dosage chart. Do not overfill. Leaks usually stop in 300 km, or 2 days of usage. If leak continues, second application may be required or mechanical attention is needed. WARNING: Do not use in brake system or add to antifreeze / coolant.

Dosage

• Engine and Transmission—Use Full Bottle
• Power Steering—Use 1/2 Bottle
•  Hydraulic, Differential, Small Engines—Use 100 mL Per Liter of Capacity
•  Preventative Maintenance—Use 1/2 Recommended Dosage

Rislone High Kilometer Automatic Transmission Repair reduces rough shifting and friction, while eliminating slip, controlling temperature, and repairing shudder, chatter and whining. Premium high mileage formula restores transmission performance and saves on costly transmission / transaxle repairs. Use when topping off existing fluid when low, or add a bottle when changing the fluid. For many vehicles, this is your last chance before paying an expensive repair bill or replacing the vehicle.
Automatic Transmissions do not work without fluid, nor do they work well without the correct fluid. Automatic Transmission Fluid (ATF) is one of the most complex of all lubricating fluids. It has to reduce friction enough to prevent wear and control temperature, while at the same time allowing some friction to prevent the internal clutch material from slipping. This same fluid must operate at low and high temperature extremes. NOTE: Do not use in CVT.

World’s Most Trusted Repair Brand Since 1921

Dual Action Formula—Twice the performance

Safe And Easy To Use

Works To Seal & Stop Leaks Plus…

Restores Performance—Stops leaks, slipping and rough shifting.
• Hi-Tech Additives
• Viscosity Improvers
• Friction Modifiers
Adds Protection—Reduces heat & friction, and stabilizes fluid
• Fluid Stabilizer
• Lubrication Additives
• Seal Conditioners

The result is a smoother shifting transmission with no leaks.

INSTRUCTIONS:

Adding to existing Transmission Fluid

1. Remove transmission dipstick and check fluid level. For most vehicles this is usually done while the engine is running and the transmission is in Park. The transmission dipstick is usually located near the engine oil dipstick but further back into the engine compartment. Some vehicles do not have a normal dipstick.  For those, the product has to be added to the transmission through a fill plug.  Consult owner’s manual for location.
2. If fluid is low, pour entire contents of the two chamber bottle into the dipstick tube. Do NOT overfill.

Tip.  If necessary, to prevent overfill, drain some fluid from transmission.

3. Check fluid level again. Top off with manufacturer’s recommended transmission fluid as needed.
4. Replace dipstick and drive 10 to 15 minutes to circulate fluid.
5. Depending on transmission problem, results will either be immediate or noticeable within two days or 150 km of driving.
6. In transmissions with seriously damaged components, a second treatment may be required. In this case, it is suggested that the transmission fluid and filter be changed and a second application of Automatic Transmission Repair be added.

Changing Fluid

If using Automatic Transmission Repair when changing transmission fluid, add entire contents of bottle after filter is changed.  Then refill with manufacturer’s recommended fluid to proper level.  Drive vehicle and recheck fluid level.

DOSAGE:

One bottle is designed to treat 7 to 12 litres of fluid capacity.  On smaller systems from 4 to 6.9 litres, only use half bottle, pouring equal amounts from each side.  For larger systems use one bottle for every 9 litres of capacity.

WHAT IS YOUR AUTOMATIC TRANSMISSION PROBLEM?

Small Leaks—Need to add fluid 1X per month

Medium Leaks—Need to add fluid 1X per week

Leaks—Front Pump, pan gasket and output shaft

Noise and Whining

           Shutter and Chatter

           Slipping and Rough Shifting

WE CAN HELP!!!

         Safe For— Domestic / Import, Cars, Trucks, SUV’s

         Automatic Transmission—Step (regular) and Overdrive

         Transaxle—Front / All-Wheel Drive

         Fluid—Works with all types of transmission fluid including regular petroleum, high mileage /                 kilometre, blends and fully synthetic.

WHAT IS A TRANSMISSION?

There are two basic types of automatic transmissions.

         Transaxle / Front-Wheel Drive — The transmission is usually combined with the axles to form            a transaxle.  In most front-wheel-drive vehicles, the engine is mounted sideways and  the                    transaxle is located under the hood with then engine.  It connects to the tires with axle shafts.

          Transmission Rear-Wheel Drive — The transmission is mounted to the back of the engine                 and it is located underneath the center hump of the floorboard.  A driveshaft connects the                     transmission to the axle.

Transmission Components

Transmissions are a combination of mechanical, hydraulic and electric parts.

          Mechanical

Many mechanical parts are required to operate a transmission.  Some of the more important                parts are the fluid pump, valve body, clutches, bands and torque converter.  These parts work              in unison with the hydraulic system.

          Hydraulic

The hydraulic system uses the fluid pump to create pressure, which is controlled by the valve               body.  The high pressure fluid is used to engage clutches & bands, along with cooling the                     transmission.

          Electrical

On later-model transmissions, computer controlled electric solenoids are responsible for                      shifting and converter lock-up.

Rislone® Transmission Stop Leak Concentrate is specially designed to stop seal and gasket leaks caused by normal transmission wear and age.

Works with ALL domestic and import, automatic and manual transmission fluids. Also, safe to use in CVT transmissions.

World’s Most Trusted Stop Leak Brand Since 1921

Stops and Seals Trans Fluid Leaks

Safe and Easy to Use

Restores Gaskets & Seals to Stop & Prevent Transmission Fluid Leaks

INSTRUCTIONS:
Add entire bottle of Stop Leak to transmission to restore fluid level. Do not overfill. Leaks usually stop in 300 km or 3 days of driving. If leak continues, second application may be required or mechanical attention is needed.

DOSAGE:
Automatic – One bottle treats up to 9.5 liters of fluid. For larger systems, use 1 bottle for every 9 liters of fluid capacity.
Manual – Use approximately 60 mL per liter of fluid capacity.

CVT (Continuously Variable Transmission) design is fundamentally different from a traditional automatic transmission. Conventional ATF (Automatic Transmission Fluid) and additives cannot be used in these specialized transmissions. Your vehicle is a good candidate for this solution if you are noticing excessive noise, shudder, slipping, leaks, or low overall performance in your CVT. Rislone CVT Transmission Fix is a synthetic blend treatment for the transmission fluid, seals and metal surfaces.

• Seal Conditioner stops current and prevents future leaks by protecting and
  reconditioning seals.
• Extreme Pressure / Anti-wear Agents provide better metal-to- metal friction properties to stop slipping, jerking, rough shifting and shudder improving shift feel giving better driving comfort.
• Cleaning Detergents include dispersant and anti-oxidants to remove sludge and varnish from metal parts.
• Performance Additive Booster controls fluid degradation caused by high temperatures, extending CVT life and reduces noise.

These additives stop belt / chain slipping, seal fluid leaks and reduce noise. Global multi-vehicle domestic / import formulation can be used in all push belt-drive and chain-driven CVT applications,
including both high- and low- viscosity applications. Some vehicles do not have a normal dipstick. For these, the product has to be added to the transmission through a fill plug. Consult owner’s manual for location. After you add the recommended dosage of Rislone CVT Transmission Fix, you will start to notice results immediately or within 350 km or 4 days of driving.

Instructions For Use
Shake container. Add entire bottle of CVT Transmission Fix to transmission. Do not overfill. Depending on the CVT problem, results will either be immediate or noticeable within 350 km or 4 days of driving. In CVT with seriously damaged components, a second treatment may be required. In this case, it is suggested that the fluid and filter be changed, and a second application of CVT Transmission Fix be added.

Dosage
• One bottle treats 5 to 9 liters of total fluid capacity
• Use a half bottle for fluid capacity from 2.5 to 4.9 liters
• For larger systems use 1 bottle for every 7.5 liters

Rislone® Power Steering Stop Leak Concentrate is specially designed to stop seal and O-ring leaks
caused by normal power steering wear and age. Works on rack & pinion units, gear boxes and pumps. Keeps power steering seals soft and pliable. Non-corrosive, non- clogging and non-foaming.

Works with ALL domestic, import and heavy duty power steering fluids; including petroleum, mineral
oil, synthetics and ATF automatic transmission fluid.

World’s Most Trusted Stop Leak Brand Since 1921

Stops and Seals Power Steering Fluid Leaks

Safe and Easy to Use

Restores O-rings & Seals to Stop & Prevent Steering Leaks

INSTRUCTIONS:
Add Stop Leak to power steering reservoir to restore fluid level. Do not overfill. Leaks usually stop in 300 km or 3 days of driving. If leak continues, a second application may be required or mechanical attention is needed.

DOSAGE:
One bottle treats up to 2.5 liters of fluid. For larger systems, use 1 bottle for every 2 liters of fluid capacity.

CAT COMPLETE™ Fuel, Exhaust & Emissions System Cleaner has high-performing detergents and heavy duty cleaning solvents that effectively scrub and remove contaminants, soot, carbon build-up, and oily residue from the fuel injectors, combustion chambers, turbo, EGR, catalytic converters, oxygen sensors and the exhaust system.  These along with other active chemical agents, react with the gases created in the combustion process to remove the remaining inorganic deposits.  This process restores their function and with regular use maintains efficiency.

As fuel is burned contaminating byproducts are created that get circulated throughout various vehicle components.  The system is designed to be able to handle this process during most normal engine operation.  However, the use of poor quality fuel, short driving distance, cold weather, improper maintenance, and component failure can greatly increase the amount of contamination and deposits created inside these systems.  Such factors can cause increased exhaust emissions, reduced fuel economy, lost power & performance, drivability issues, engine overheating, hard starts, check engine light illumination and premature engine wear.

• Increases power, performance, km/L and saves gas by not only cleaning the entire emissions & exhaust system, but the fuel system as well. Works with gasoline, ethanol and hybrid vehicles.
• Regular use every 8,000 kilometers tunes-up the fuel, emissions and exhaust systems keeping them clean and preventing the CEL light from returning. This also saves on expensive fuel system and emission control repairs.
• Will not void manufacturer’s new vehicle warranty. Specifically designed and safe to use on vehicles which have oxygen sensors and catalytic converters.  Exceeds EPA compliance performance criteria.
• Works on all fuel injected, direct injected, carbureted, turbo, GTDI, Ecotec^® & EcoBoost^® engines.
• Clean fuel and exhaust systems reduce excess exhaust hydrocarbon, CO and NO_X emissions and saves gas.
• Contains outstanding synthetic detergents to remove (IVD) intake valve deposits, (CCD) combustion chamber deposits and other fuel deposits.
• Includes combustion catalyst for improved gas mileage, smoother idling, drivability and better throttle response.
• Reduces zinc and phosphorus catalyst contamination restoring catalytic converter function.
• Cleans O2 lambda oxygen sensor tip.
• Clear OBD P0420 & other OBD codes* and turn check engine light off.
• Deodorizes sulphur “sulfur” (rotten eggs) exhaust smell.
• Pass emissions smog test

 INSTRUCTIONS:

Add entire bottle of Fuel, Exhaust & Emissions Systems Cleaner into approximately 1/2 full tank car (1/4 full tank truck) of gasoline.  Drive vehicle 30 to 50 km (ideally half of these kilometers at highway speeds), and then fill up tank.  Continue to drive vehicle normally until below 1/4 tank before refueling.  Take emissions test at this time (if needed) and CEL light should be off.  Depending on the severity and length of time light has been on, it may take an extra 400 km with multiple cycles of the vehicle being started and turned off for the light to reset.  If light is still on mechanical attention is needed.

NOTE:

This bottle is designed to work in ALL gas tanks including standard, obstructed and capless (no fuel cap) systems.  If vehicle has a fuel cap make sure to reinstall tightly, as this can cause the light to be on.

* OBD-II PID CODES P0420, P0421, P0430, P0431 and more.

CHECK ENGINE LIGHT

When the check engine light (CEL) or malfunction indicator light (MIL) illuminates, it has detected an engine system malfunction.  Some auto parts stores offer free on board diagnostic (OBD) code checks, and inexpensive readers are available to purchase for do it yourself (DIY) checks.  One of the most common codes is P0420 (along with related codes) for the emissions system that usually traces back to catalytic converter efficiency.  If the converter is dirty or bad, likely something else caused this.  CAT COMPLETE Fuel, Exhaust & Emissions System Cleaner not only helps with what may be causing the light to come on, but also the system that initiated the problem.  Driving with CEL on can cause increased vehicle emissions, poor fuel mileage, reduced power, further engine damage beyond what the original problem is, and could eventually lead to vehicle breakdown.  Sometimes the damage is so severe that cleaning will not help.  For example, a converter that has operated with temperatures over 700°C will start to melt inside and become permanently damaged. Or an oxygen sensor that is not dirty, but internally damaged.  Your best chance of cleaning one of these systems is within the first few months of when the light comes on.  However this formula can also work on a vehicle that has had the light on for years.  Once the issue has been resolved, the light may continue to be on for a period of time.  For some vehicles, it takes a few start/stop cycles for it to clear, others you may need to disconnect the battery for 15 minutes and leave the door open, then reconnect.   See vehicle owners manual for resetting the CEL if applicable.

EMISSIONS SMOG TEST

Many states, cities or regions require regular emissions inspections before renewing vehicle plates or the first time registering.   During a visual inspection if there are missing or tampered emissions components, that can be an automatic failure. It also could be something simple like a missing gas cap or a cap with a bad seal.  Defective mechanical parts that have failed would be another reason.  Many times, it does not take a mechanical issue to cause a failed result on a vehicle emissions test.  If you are unsure your vehicle will pass, or maybe it barely passed the last test, we recommend a fresh oil change and emissions system cleaning with Rislone Fuel, Exhaust & Emissions System Cleaner before testing.  Other items to consider include spark plugs and fuel filter, if they are due for replacement.  This gives your vehicle the best chance of passing.

Rislone^® Hy-per Diesel™ Complete Fuel System Treatment improves the quality of Diesel fuel by increasing its cleaning ability, adding lubrication, removing contaminants, fighting corrosion, and helping to prevent the fuel from gelling & going bad. This one dual cavity bottle contains the same amount of additives equal to a bottle of regular injector & complete fuel system cleaner, anti-gel cold flow improver, fuel stabilizer & conditioner, Cetane booster & diesel treatment, ULSD sulfur substitute, and UCL pump & injector lubricant.  Simply put, it is the best all in one diesel fuel additive money can buy.

Works with ALL:  Ultra Low Sulfur Diesel (ULSD), Regular Diesel, Biodiesel Blends, Direct Injected (DI), Indirect Injected (IDI), Turbo Direct Injected (TDI), High-Pressure Common Rail (HPCR), and Turbocharged Engines.

Use with ALL:  BlueTEC^®, Cummins^®, Duramax^®, EcoDiesel^®, Navistar^®, PowerStroke^®, TDI^® CleanDiesel and many more.

• Cleans Injectors, Valves and the Combustion Chamber
• Boosts Cetane, Power, Performance and Mileage
• Stabilizes Fuel, Lubricates and Protects
• Strong enough for Heavy-Duty Diesel engines, but packaged for easy no spill installation in Light / Medium Duty Diesel vehicles.
• Increases power, performance, kilometres per liter and saves fuel by lubricating the complete fuel system. Safe to use on vehicles which have converters, DPF particular filters, or DEF systems.
• Helps eliminate black smoke, fuel gelling, clogged injectors, rough idle and hard starts. Works equally well in trucks, SUV’s and passenger car diesel applications.
• The 8,000 KM Complete Fuel System Tune-Up
• Cleaning and Protecting Engines Since 1921

Technical: 

• Heavy Duty Top-Lube improves fuel lubricity to protect fuel injectors and pumps from wear, especially in todays severely refined diesel fuels.
• Cold Flow Additives inhibit wax crystal growth, reducing fuel pour point and cold filter plug point even in harder to treat diesel fuels. Reduces CFPP up to 5°C (20°F).
• Fuel Stabilizer Antioxidant retards oxidation, reduces sludge formation, inhibits fuel decomposition and provides fuel stability for storage.
• Cetane Improver raises the Cetane number of diesel fuel to improve cold stars and reduce misfires, warm-up time, black exhaust smoke, and emissions. Typical numbers show a 1 to 2 point increase in Cetane Number CN per ASTM D613 engine test.
• New Generation Detergent is a multifunctional ashless dispersant additive improving the quality of diesel fuel. Dual clean-up and keep-clean formula removes injector deposits, prevents and restores lost power and improves fuel economy.  Real world testing shows an average fuel economy increase of 7.3% and an 87% power recovery from cleaning effects with regular use.

Note: 

This product includes a specially designed spout which allows it to be poured into all fuel tanks, include those with misfuelling devices.  Use anytime in a nearly full tank, or add to tank and then fill with up to 130 litres of diesel fuel.  For smaller tanks from 40 to 70 litres, use 1/2 bottle pouring equal amounts from each side.  Larger tanks use one bottle for every 110 litres of fuel.

This diesel fuel additive complies with the federal low sulfur content requirements for use in diesel motor vehicles and non-road engines.

Directions: 

Bend & twist spout and tear away on the perforated tab.  Remove cap and foil seal.  Tightly screw spout onto bottle.  Gently tip bottle and complete insert spout into fuel tank opening, allow entire contents to empty into tank.  For continued protection and cleaning, use one bottle every 8,000 km.  Results will either be immediate, or noticeable within a few days of driving.

Rislone^® Hy-per Fuel™ Heavy Duty Injector Cleaner with Fuel Conditioner & Top Lube is the best all-around fuel additive to use with every tank of fuel.  This complete fuel system tune-up helps eliminate noisy injectors & fuel pumps, rough idle, hard starting and hesitation.  Heavy Duty additives increase power, performance, mileage and help save fuel by cleaning & lubricating fuel injectors.  Regular use, summer and winter, maintains optimum engine efficiency and power.  Use in gas, ethanol and diesel cars, SUV’s, trucks, RV’s, fuel injected, carbureted, turbo, GTDI and direct injected engines.  Works with all types of fuel including regular & unleaded gasoline, ULSD Ultra Low Sulfur Diesel, E85 Ethanol and other reformulated and bio-fuel formulas.

• Upper Cylinder Lubricant UCL helps prevent cylinder, ring & piston wear along with lubricating valves & guides giving longer engine life.

• Will not void manufacture’s new vehicle warranty and safe to use on vehicles which have oxygen sensors, catalytic converters or DPF filters.

• Exceeds EPA compliance performance criteria and is EPA registered.

• Results will either be immediate or noticeable within a few days of driving. Non-solvent formula contains petroleum oils.

• Premium P.E.A. Polyetheramine New Generation Detergent Patented Formula is a multifunctional additive improving the quality of fuel.

• Cleaning Engines Since 1921

• Increases Power, Boosts Performance & Mileage and Saves Fuel by Cleaning & Lubricating Fuel Injectors.

• Helps Eliminate Noisy Injectors & Fuel Pumps, Smooths Rough Idle, Hard Starting and Hesitation.

• Smoothes rough idle and eliminates hard starts giving cleaner, quieter operation.

• The Fuel Conditioner & Top Lube protects and lubricates all parts of the fuel system including the fuel pump and injectors allowing more power & performance.

UCL – Upper Cylinder Lubricant Top Lube

The Rislone UCL additive is specially designed to lubricate the upper cylinder of an engine; however this action starts in the fuel tank.  This UCL formulation helps overcome the lack of lubrication in modern fuels including unleaded gasoline, ULSD diesel fuel, E85 Ethanol, and other oxygenated and bio fuels.  In the fuel tank, UCL helps prevent rust & corrosion and this process continues into the fuel lines.  UCL also lubricates and protects the fuel pump, giving it a longer life and quieter operation.  The next step for the UCL formula is to lubricate the injectors allowing them to work more efficiently.   Not only are cylinder deposits cleaned, including gum and varnish, but as the UCL treats the upper cylinder the lubricating film helps to prevent carbon from sticking so that it can be burned.  This film completely lubricates the upper piston, rings, guides, valves, and seals.

Directions / Dosage: 

P/N 24732 / 950 mL bottle – One bottle treats 380 liters of gasoline or diesel fuel. For smaller or larger systems add approximately 50 mL for every 20 liters of fuel.

For vehicles with known fuel lubrication problems, double the dosage.

Results will either be immediate or noticeable within a few days of driving.

Rislone^® Hy-per Fuel™ Complete Fuel System Treatment improves the quality of gas by increasing its cleaning ability, adding lubrication, removing contaminants, reducing spark knock, and helping to prevent the fuel from going bad.  This one dual cavity bottle contains the same amount of additives equal to a bottle of regular injector & complete fuel system cleaner, upper cylinder lubricant, fuel stabilizer & conditioner, dry gas, gas treatment and octane booster. Simply put, it is the best all in one gasoline fuel additive money can buy.

Works with ALL:  Fuel Injected, Port Fuel Injection (PFI), Direct Injected (DI / DIG), Gasoline Turbo Direct Injected (GTDI), Turbocharged and Carbureted Engines.

Use with ALL:  Unleaded, Premium, and Ethanol (E10, E85) Flex Fuel Vehicles

• Cleans Injectors, Valves, Fuel Lines, Intake Manifold and the Combustion Chamber
• Boosts Octane, Power, Performance and Mileage
• Stabilizes Gas, Lubricates and Protects
• Increases power, performance, mileage and saves gas by cleaning & lubricating the complete fuel system. Engine dynamometer tests show improved fuel economy.
• Helps eliminate noisy injectors & fuel pumps, rough idle, hard starting and hesitation. Regular use provides reduced fuel system and emission control repairs.
• Will not void manufacture’s new vehicle warranty and safe to use on vehicles which have oxygen sensors and catalytic converters. Exceeds EPA compliance performance criteria and is EPA registered.
• Cleaning and Protecting Engines Since 1921
• The 8 000 km Complete Fuel System Tune-Up

Technical: 

• Upper Cylinder Lubricant (UCL) Top-Lube reduces friction and wear and improves fuel economy.
• Water Remover Gas Dryer removes free water in gas tank helping to prevent gas line freeze-ups in the winter, and moisture related corrosion year round. This also works to reduce emissions and inhibits bacterial growth in gas tanks.
• Fuel Stabilizer and Triple Corrosion Protection inhibits oxidation, gum, varnish and corrosion, helping gasoline resist breakdown improving stability. Provides A-rating corrosion protection.
• Gas Treatment Additives provide maximized power and acceleration, optimized fuel economy and excellent performance in gasoline engines.
• Octane Booster raises the Octane number of gasoline and Octane Requirement Increase (ORI) reduces spark knock, misfires and emissions.
• Premium P.E.A. Polyetheramine New Generation Detergent Patented Formula is a multifunctional additive improving the quality of gasoline. Dual clean-up and keep-clean formula removes injector, combustion chamber and intake valve deposit which restores lost power and improves fuel economy.

Note: 

This product includes a specially designed spout which allows it to be poured into all gas tanks, include those that use a capless (no fuel cap) system..  Use anytime in a nearly full tank, or add to tank and then fill with up to 80 L of gasoline.  For smaller tanks from 20 to 40 L, use 1/2 bottle pouring equal amounts from each side.  Larger tanks use one bottle for every 60 L of gasoline.

Directions: 

Bend & twist spout and tear away on the perforated tab.  Remove cap and foil seal.  Tightly screw spout onto bottle.   Gently tip bottle and complete insert spout into gas tank opening, allow entire contents to empty into tank.  For continued protection and cleaning, use one bottle every 8 000 km.  Results will either be immediate, or noticeable within 150 km of driving.

To keep the system clean and lubricated in-between treatments, use Rislone Hy-per Fuel Injector Cleaner Upper Cylinder Lubricant part number 24701 (177 mL) or 24732 (950 mL).

If you’re all about high performance then you know your car, like you, can use an energy boost from time to time. Our Rislone Super Concentrated Octane Booster does just that. This formula works like an energy drink to give your car the added push that will get it over the line faster.

Rislone Super Concentrated Octane Booster increases fuel’s octane rating to stop engine hesitation and knock and ping, while also increasing power and performance. The formula works equally well on classic muscle cars, newer, smaller, harder-working engines, off-road and racing applications. The increased octane allows the engine to run optimum spark timing, which not only creates more power, but in many engines reduces emissions and increases fuel mileage.

Grab a bottle, follow our easy installation process and instantly feel your car’s increased power. Remember, your car is what it eats. Make it Rislone. It’s like an energy drink for your car.